- #How to mount a front license plate on a sl550 how to#
- #How to mount a front license plate on a sl550 install#
- #How to mount a front license plate on a sl550 software#
- #How to mount a front license plate on a sl550 trial#
The goal of the extension arm is to get the plate into a better position to avoid the parking sensors. It mounts between the tow stud and the back plate. We us this part to get further control over the positioning of the back plate. Some vehicle’s mounts come with an extension arm: We will start with the plate all the way to one side, and make small adjustments until the sensors are no longer triggered by the mount. 2005 Mercedes-Benz SL600 License Plate Bracket. 2004 Mercedes-Benz SL600 License Plate Bracket.
#How to mount a front license plate on a sl550 software#
Same quality as OE for less Designed with the latest software and manufactured with modern tooling. SL550 - 5.5L 8 Cyl (32 Valve) 2012 Mercedes-Benz SL550 License Plate Bracket. There is no risk of damge or cost to you if it does not work out. Please contact us if you would like to confimr the fit on your vehicle. We have not had the chance to do a test fit on this model yet.
#How to mount a front license plate on a sl550 trial#
This is usually a trial and error process. License plate brackets make it easy and convenient to mount license plates, but their usual mounting locations on the bumper make them particularly vulnerable to impact damage in a collision. The Platypus License Plate Mount for 2013-2016 Mercedes-Benz GL 550.
#How to mount a front license plate on a sl550 install#
if it is a factory bracket there are 4 dimples on the middle of the bumper,you have to drill 1/2 in holes to install 4 grommets to hold bracket in place with screws-the factory bracket kit comes with bracket,4 grommets and the four screws-good luck.
#How to mount a front license plate on a sl550 how to#
If they are being triggered, you can adjust the angle of the plate horizontally by grabbing it on both sides and angling it to the right or left. SOURCE: How to install a front license plate bracket on a. If you car has parking sensors, some adjustment of the plate may be necessary so that the mount doesn’t set them off.
Install the license plate with the four included button head screws.ĥ. This bolt needs to be snug to prevent the plate from coming loose or rotating, almost as tight as you can get it with a standard socket wrench.Ĥ. If your car uses a left hand threaded tow stud, you will want to use an open ended wrench on the tow stud to keep it tight while you torque down the plate bolt. Hold the plate in the desired position while you tighten the plate bolt with a 15mm socket. We recommend keeping your fingers behind the plate at all times so that it can’t touch the bumper.
Use caution during this process so that you do not scratch the bumper. To adjust the tab, screw the plate bolt in a few turns and use the leverage of the vehicle and the stud bend it slightly. On some vehicles, the back plate will touch the bumper if you install it without adjusting the angle of the mounting tab first. Hold the back plate up to the stud with the holes lined up. Check for clearance, and install the back plate. The studs are aluminum which is much softer than the material in the towing eye receiver, so they won’t damage your car.ģ. We intentionally machine these slightly oversized, so if it feels like it doesn’t want to go in just get a socket on the end of it and drive it in. Install the tow stud into the towing eye receiver. Take the cover completely off, and keep it in a safe place.Ģ. Using your finger, or a plastic prying tool, remove the towing eye cover on the front bumper. Although we have never had a plate backing come loose accidentally, each plate backing is balanced such that if it did the plate would hang and not fall off.1. Using the included flat wrench you can loosen the bolt a ¼ turn and then slide the plate off before the wash.
If you absolutely need to use a rag car wash, then the Platypus should be removed to avoid getting caught up in the machine. Luckily, you can order a high-quality Mercedes Benz license plate bracket from to keep your license plate secure. We believe that touchless is the only kind of automatic car wash anyone should subject their Mercedes-Benz's paint job to. A wobbly license plate can undermine your Mercedes Benz’s premium appearance and get you in trouble with the law in some states. At times when the plate is not needed, it can be removed easily, leaving no trace that it was ever there. This method of installing the front plate is common and legal in all states that require front license plates. This Platypus is designed to fit the existing port on the front bumper of a SL 550 for model years from 2013 to 2019. In many states, you need a front plate on your Mercedes-Benz, but that does not mean you have to drill it in permanently. It is one of the best Mercedes-Benz SL 550 accessories for keeping your license plate holder legal with no drilling required. The Platypus is a front license plate bracket that is made in the USA to exacting specifications. Mercedes-Benz SL 550 Front License Plate Holder
0 kommentar(er)
